[ovs-dev] [PATCH v2.51 1/5] ofp-actions: Allow Consistency checking of OF1.3+ VLAN actions after mpls_push

Simon Horman horms at verge.net.au
Thu Dec 5 00:51:39 UTC 2013


On Wed, Dec 04, 2013 at 04:44:17PM -0800, Ben Pfaff wrote:
> On Thu, Dec 05, 2013 at 08:58:49AM +0900, Simon Horman wrote:
> > On Wed, Dec 04, 2013 at 01:24:29PM -0800, Ben Pfaff wrote:
> > > On Thu, Nov 21, 2013 at 12:46:42PM +0900, Simon Horman wrote:
> > > > The aim of this patch is to support provide infrastructure for verification
> > > > of VLAN actions after an mpls_push action for OpenFlow1.3. This supplements
> > > > existing support for verifying these actions for pre-OpenFlow1.3.
> > > > 
> > > > In OpenFlow1.1 and 1.2 MPLS tags are pushed after any VLAN tags that
> > > > immediately follow the ethernet header. This is pre-OpenFlow1.3 tag
> > > > ordering. Open vSwitch also uses this ordering when supporting MPLS
> > > > actions via Nicira extensions to OpenFlow1.0.
> > > > 
> > > > When using pre-OpenFlow1.3 tag ordering an MPLS push action does not
> > > > affect the VLANs of a packet. If VLAN tags are present immediately after
> > > > the ethernet header then they remain present there.
> > > > 
> > > > In of OpenFlow1.3+ MPLS LSEs are pushed before any VLAN tags that
> > > > immediately follow the ethernet header. This is OpenFlow1.3+ tag
> > > > ordering.
> > > > 
> > > > When using OpenFlow1.3+ tag ordering an MPLS push action affects the
> > > > VLANs of a packet as any VLAN tags previously present after the ethernet
> > > > header are moved to be immediately after the newly pushed MPLS LSE. Thus
> > > > for the purpose of action consistency checking a packet may be changed
> > > > from a VLAN packet to a non-VLAN packet.
> > > > 
> > > > In this way the effective value of the VLAN TCI of a packet may differ
> > > > after an MPLS push depending on the OpenFlow version in use.
> > > > 
> > > > This patch does not enable the logic described above.
> > > > Rather it is disabled in ofpacts_check__(). It should
> > > > be enabled when support for OpenFlow1.3+ tag order is added
> > > > and enabled.
> > > > 
> > > > Signed-off-by: Simon Horman <horms at verge.net.au>
> > > 
> > > As far as I can tell this doesn't make sense, because where the MPLS
> > > tag goes is a property of the action that we know at the time we parse
> > > the push_mpls action.  So why isn't this patch just the following?
> > > 
> > > diff --git a/lib/ofp-actions.c b/lib/ofp-actions.c
> > > index a02f842..f444374 100644
> > > --- a/lib/ofp-actions.c
> > > +++ b/lib/ofp-actions.c
> > > @@ -2071,6 +2071,9 @@ ofpact_check__(enum ofputil_protocol *usable_protocols, struct ofpact *a,
> > >           * Thus nothing can be assumed about the network protocol.
> > >           * Temporarily mark that we have no nw_proto. */
> > >          flow->nw_proto = 0;
> > > +        if (ofpact_get_PUSH_MPLS(a)->position == OFPACT_MPLS_BEFORE_VLAN) {
> > > +            flow->vlan_tci = 0;
> > > +        }
> > >          return 0;
> > 
> > That was more or less what I originally tried.  However I believe that it
> > doesn't work because ofpact_get_PUSH_MPLS(a)->position may not have been
> > set at the time that ofpact_check__ is called.  In particular this occurs
> > when it is called indirectly from parse_ofp_str__.
> > 
> > Moreover, when ofpact_check__ is called indirectly from parse_ofp_str__ it
> > is used to check actions when a one of number of protocols may be used,
> > that is multiple bits of *usable_protocols.  If we could rely on
> > ofpact_get_PUSH_MPLS(a)->position then I believe that implies that if it is
> > set to OFPACT_MPLS_BEFORE_VLAN all pre-OpenFlow1.3 bits of
> > *usable_protocols need to be cleared.  Otherwise all OpenFlow1.3+ bits
> > would need to be cleared.
> 
> I think this might be a mistake in how we define the syntax that
> parse_ofp_str__() parses.  If I write "actions=push_mpls" on an
> ovs-ofctl command line, then I want that to have some specific
> meaning.  I don't want it to mean "do one thing if you happen to
> negotiate OpenFlow 1.2 or some other thing if you happen to negotiate
> OpenFlow 1.3", because that's totally unusable and broken from a user
> perspective.

To clarify, that is exactly what this series was trying to do.

I think there is some precedence in the handling of actions
that set_vlans. Some OF versions implicitly push a tag, some don't.

But I do agree that the behaviour you describe above would
be very confusing for users.

> So if that the issue then I think we should change the
> syntax.  One way would be to have "push_mpls" default to the 1.3
> behavior (which seems generally saner) and allow the user to specify
> an option to get the 1.2 behavior.

Sure, I think I am happy with that idea.

By an option do you mean a different action name, for example append_mpls,
or push_mpls_after_vlan?

Or do you have something else in mind?




More information about the dev mailing list