[ovs-dev] [RFC v7 07/13] dp-packet: Handle multi-seg mubfs in shift() func.
Loftus, Ciara
ciara.loftus at intel.com
Mon May 28 15:42:23 UTC 2018
>
> In its current implementation dp_packet_shift() is also unaware of
> multi-seg mbufs (that holds data in memory non-contiguously) and assumes
> that data exists contiguously in memory, memmove'ing data to perform the
> shift.
>
> To add support for multi-seg mbuds a new set of functions was
> introduced, dp_packet_mbuf_shift() and dp_packet_mbuf_write(). These
> functions are used by dp_packet_shift(), when handling multi-seg mbufs,
> to shift and write data within a chain of mbufs.
>
> Signed-off-by: Tiago Lam <tiago.lam at intel.com>
> ---
> lib/dp-packet.c | 102
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 101 insertions(+), 1 deletion(-)
>
> diff --git a/lib/dp-packet.c b/lib/dp-packet.c
> index 1b39946..7b603c7 100644
> --- a/lib/dp-packet.c
> +++ b/lib/dp-packet.c
> @@ -294,13 +294,113 @@ dp_packet_prealloc_headroom(struct dp_packet
> *b, size_t size)
> }
> }
>
> +#ifdef DPDK_NETDEV
> +/* XXX: Caller must provide the correct mbuf where the offset is located. It
> + must also guarantee that 'ofs' is within bounds */
> +static void
> +dp_packet_mbuf_write(struct rte_mbuf *mbuf, int16_t ofs, uint32_t len,
> + const void *data)
> +{
> + char *dst_addr;
> + uint16_t data_len;
> + int len_copy;
> + while (mbuf) {
> + if (len == 0) {
> + break;
> + }
> +
> + dst_addr = rte_pktmbuf_mtod_offset(mbuf, char *, ofs);
> + data_len = MBUF_BUF_END(mbuf->buf_addr, mbuf->buf_len) -
> dst_addr;
> +
> + len_copy = MIN(len, data_len);
> + /* We don't know if 'data' is the result of a rte_pktmbuf_read call, in
> + * which case we may end up writing to the same region of memory we
> are
> + * reading from and overlapping. Thus, the use of memmove */
> + memmove(dst_addr, data, len_copy);
> +
> + data = ((char *) data) + len_copy;
> + len -= len_copy;
> + ofs = 0;
> +
> + mbuf = mbuf->next;
> + }
> +}
> +
> +static void
> +dp_packet_mbuf_shift_(struct rte_mbuf *dbuf, int16_t dst_ofs,
> + const struct rte_mbuf *sbuf, uint16_t src_ofs, int len)
> +{
> + char rd[len];
> +
> + const char *wd = rte_pktmbuf_read(sbuf, src_ofs, len, rd);
> + if (!wd) {
> + /* XXX: Log WARN here. */
> + return;
> + }
> +
> + dp_packet_mbuf_write(dbuf, dst_ofs, len, wd);
> +}
> +
> +/* XXX: Delta must fall within the bounds of an mbuf */
> +static void
> +dp_packet_mbuf_shift(struct dp_packet *b, int delta)
> +{
> + struct rte_mbuf *sbuf, *dbuf;
> + uint16_t src_ofs;
> + int16_t dst_ofs;
> +
> + struct rte_mbuf *mbuf = CONST_CAST(struct rte_mbuf *, &b->mbuf);
> + dbuf = mbuf;
> + sbuf = mbuf;
> +
> + /* Set the destination address to copy to */
> + if (delta < 0) {
> + dst_ofs = delta;
> + src_ofs = 0;
> + } else {
> + dst_ofs = delta;
> + src_ofs = 0;
> + }
The outcome of the if and else is the same.
> +
> + /* Shift data from src mbuf and offset to dst mbuf and offset */
> + dp_packet_mbuf_shift_(dbuf, dst_ofs, sbuf, src_ofs,
> + rte_pktmbuf_pkt_len(sbuf));
> +
> + /* Update mbufs' properties, depending if there's one mbuf or more */
> + mbuf->data_off = mbuf->data_off + dst_ofs;
> +
> + struct rte_mbuf *tmbuf = rte_pktmbuf_lastseg(mbuf);
> + if (dbuf != tmbuf) {
> + tmbuf->data_len += delta;
> + mbuf->data_len -= dst_ofs;
> + }
> +}
> +#endif
> +
> /* Shifts all of the data within the allocated space in 'b' by 'delta' bytes.
> * For example, a 'delta' of 1 would cause each byte of data to move one
> byte
> * forward (from address 'p' to 'p+1'), and a 'delta' of -1 would cause each
> - * byte to move one byte backward (from 'p' to 'p-1'). */
> + * byte to move one byte backward (from 'p' to 'p-1').
> + * Note for DPBUF_DPDK(XXX): The shift can only move within the bounds
> of an
> + * mbuf since it assumes the source and destination offsets will be on the
> + * same mbuf. */
> void
> dp_packet_shift(struct dp_packet *b, int delta)
> {
> +#ifdef DPDK_NETDEV
> + if (b->source == DPBUF_DPDK) {
> + ovs_assert(delta > 0 ? delta <= dp_packet_tailroom(b)
> + : delta < 0 ? -delta <= dp_packet_headroom(b)
> + : true);
> +
> +
> + if (delta != 0) {
Could remove some code duplication here. The assert & check for delta !=0 is common for both DPDK_NETDEV and !DPDK_NETDEV
> + dp_packet_mbuf_shift(b, delta);
> + }
> +
> + return;
> + }
> +#endif
> ovs_assert(delta > 0 ? delta <= dp_packet_tailroom(b)
> : delta < 0 ? -delta <= dp_packet_headroom(b)
> : true);
> --
> 2.7.4
>
> _______________________________________________
> dev mailing list
> dev at openvswitch.org
> https://mail.openvswitch.org/mailman/listinfo/ovs-dev
More information about the dev
mailing list