[ovs-dev] [PATCH v7] Encap & Decap actions for MPLS packet type.
Martin Varghese
martinvarghesenokia at gmail.com
Wed Nov 10 15:41:10 UTC 2021
On Fri, Nov 05, 2021 at 03:05:54PM +0100, Ilya Maximets wrote:
> On 10/12/21 06:23, Martin Varghese wrote:
> > From: Martin Varghese <martin.varghese at nokia.com>
>
> Hi, Martin. Thanks for working on this!
>
> I didn't review most of the logic of the action itself, but see some
> comments inline.
>
> Bets regards, Ilya Maximets.
>
Hi Ilya,
Thanks for your time.
I will work on your comments. Meanwhile please let me know the additional comments you have.
Please find my inline responses for your comments.
> >
> > The encap & decap actions are extended to support MPLS packet type.
> > Encap & decap actions adds and removes MPLS header at start of the
> > packet.
> >
> > The existing PUSH MPLS & POP MPLS actions inserts & removes MPLS
> > header between ethernet header and the IP header.
>
> From the documentation it's really hard to understand the difference
> between PUSH/POP_MPLS and encap/decap(mpls). Could you please, add
> notes about the difference to both: description of PUSH/POP_MPLS
> and encap/decap(mpls) in the ovs-actions.7.rst ?
>
I think the description of encap/decap MPLS is little confusing and could be made better.
I think it is better to fix the description than referring ENCAP/DECAP in push_mpls/pop_mpls & vice versa.
I am planning to change like below
Encap
The ``encap(mpls(ethertype=....))`` adds an MPLS header at the start of the packet.
Decap
Otherwise, if the packet is encapsulated inside a MPLS header, removes the MPLS header and classifies the inner packet as mentioned in the packet type argument of the decap.
Does this make sense?
> > Though this behaviour
> > is fine for L3 VPN where an IP packet is encapsulated inside a MPLS
> > tunnel, it does not suffice the L2 VPN requirements. In L2 VPN the
> > ethernet packets must be encapsulated inside MPLS tunnel.
> >
> > In this change the encap & decap actions are extended to support MPLS
> > packet type. The encap & decap adds and removes MPLS header at the
> > start of packet as depicted below.
> >
> > Encapsulation:
> >
> > Actions - encap(mpls(ether_type=0x8847)),encap(ethernet)
> >
> > Incoming packet -> | ETH | IP | Payload |
> >
> > 1 Actions - encap(mpls(ether_type=0x8847)) [Datapath action - ADD_MPLS:0x8847]
> >
> > Outgoing packet -> | MPLS | ETH | Payload|
> >
> > 2 Actions - encap(ethernet) [ Datapath action - push_eth ]
> >
> > Outgoing packet -> | ETH | MPLS | ETH | Payload|
> >
> > Decapsulation:
> >
> > Incoming packet -> | ETH | MPLS | ETH | IP | Payload |
> >
> > Actions - decap(),decap(packet_type(ns=0,type=0)
> >
> > 1 Actions - decap() [Datapath action - pop_eth)
> >
> > Outgoing packet -> | MPLS | ETH | IP | Payload|
> >
> > 2 Actions - decap(packet_type(ns=0,type=0) [Datapath action - POP_MPLS:0x6558]
> >
> > Outgoing packet -> | ETH | IP | Payload|
> >
> > Signed-off-by: Martin Varghese <martin.varghese at nokia.com>
> > ---
> > Changes in v2:
> > - Fixed the compilation error reported by bot.
> >
> > Changes in v3:
> > - Adapted the changes to allign with the kernel implementaion
> >
> > Changes in v4:
> > - Fixed the compilation error reported by bot.
> > - Added SLOW_ACTION support for no datapath support.
> >
> > Changes in v5:
> > - Code styling fixed.
> > - Given reference for packet_type field in documentation.
> > - Modified code to do recirc only for the last label.
> > - Cleaed l2,l3,l4 fields with encap.
> > - Fixed existing encap & decap tests to do set eth to outer header
> > - Added tests to verify Encap & Decap with legacy Push & Pop.
> > - Added xlate tests.
> > - Added seperate tests to inspect packet after encap & decap.
> > - Added tests for multiple mpls test cases.
> >
> > Changes in v6:
> > - Styling and variable naming fixed.
> > - Tests added for slow path support.
> > - Added comments in code.
> > - Added odp test for add_mpls action.
> > - Documentation added in ovs-actions.7.rst
> >
> > Changes in v7:
> > - Fixed Documentation.
> > - Initialized variables in odp test.
> > - Add test skip for no dp support.
> >
> > Documentation/ref/ovs-actions.7.rst | 17 +-
> > NEWS | 2 +-
> > .../linux/compat/include/linux/openvswitch.h | 33 +-
> > include/openvswitch/ofp-ed-props.h | 18 +
> > lib/dpif-netdev.c | 1 +
> > lib/dpif.c | 1 +
> > lib/odp-execute.c | 12 +
> > lib/odp-util.c | 73 ++++-
> > lib/ofp-actions.c | 5 +
> > lib/ofp-ed-props.c | 91 ++++++
> > lib/packets.c | 45 +++
> > lib/packets.h | 2 +
> > ofproto/ofproto-dpif-ipfix.c | 1 +
> > ofproto/ofproto-dpif-sflow.c | 1 +
> > ofproto/ofproto-dpif-xlate.c | 78 +++++
> > ofproto/ofproto-dpif.c | 38 +++
> > ofproto/ofproto-dpif.h | 4 +-
> > tests/mpls-xlate.at | 57 ++++
> > tests/odp.at | 1 +
> > tests/system-traffic.at | 308 ++++++++++++++++++
> > 20 files changed, 771 insertions(+), 17 deletions(-)
> >
> > diff --git a/Documentation/ref/ovs-actions.7.rst b/Documentation/ref/ovs-actions.7.rst
> > index 7224896df..9d60bf631 100644
> > --- a/Documentation/ref/ovs-actions.7.rst
> > +++ b/Documentation/ref/ovs-actions.7.rst
> > @@ -212,12 +212,13 @@ Unsupported packet type
> > is not an L3 packet, and ``encap(nsh)`` raises this error if the current
> > packet is not Ethernet, IPv4, IPv6, or NSH.
> >
> > + The ``decap`` action is supported only for packet types ethernet, NSH and
> > + MPLS. Openvswitch raises this error for other packet types.
>
> Please, put two spaces between sentences like it's done in the rest of the document.
>
> > When a ``decap`` action decapsulates a packet, Open vSwitch raises this error
> > if it does not support the type of inner packet. ``decap`` of an Ethernet
> > header raises this error if a VLAN header is present, ``decap`` of a NSH
> > packet raises this error if the NSH inner packet is not Ethernet, IPv4, IPv6,
> > - or NSH, and ``decap`` of other types of packets is unsupported and also
> > - raises this error.
> > + or NSH.
> >
> > This error terminates packet processing, retaining any previous side effects
> > (e.g. output actions). When this error arises within the execution of a
> > @@ -995,6 +996,7 @@ The ``encap`` action
> > | ``encap(nsh([md_type=``\ *md_type*\
> > ``], [tlv(``\ *class*,\ *type*,\ *value*\ ``)]...))``
> > | ``encap(ethernet)``
> > + | ``encap(mpls(ether_type=``\ *ether_type*\)
>
> The last ')' should also be highlighted with ``.
>
> >
> > The ``encap`` action encapsulates a packet with a specified header. It has
> > variants for different kinds of encapsulation.
> > @@ -1018,6 +1020,10 @@ frame. The Ethernet type is initialized to the L3 packet's type, e.g. 0x0800
> > if the L3 packet is IPv4. The Ethernet source and destination are initially
> > zeroed.
> >
> > +The ``encap(mpls(ethertype=....))`` variant encapsulates an ethernet or
>
> Hmm. So, is it 'ether_type' or 'ethertype' ?
>
> > +L3 packet with a MPLS header. The ethertype could be MPLS unicast (0x8847) or
> > +multicast (0x8848) ethertypes.
>
> Please, highlight the hex numbers.
>
> > +
> > **Conformance**
> > This action is an Open vSwitch extension to OpenFlow 1.3 and later,
> > introduced in Open vSwitch 2.8.
>
> This section, I think, should be updated in order to reflect in which OVS
> version mpls variant is added.
>
> > @@ -1030,6 +1036,7 @@ The ``decap`` action
> >
> > **Syntax**:
> > | ``decap``
> > + | ``decap([packet_type(ns=namespace,type=type)])``
>
> Please, highlight the arguments. And brackets, I guess,
> not needed here. It's either brackets or 2 syntax variants.
I assume you meant the American brackets 😊 . I will remove “[]” ?
>
> >
> > Removes an outermost encapsulation from the packet:
> >
> > @@ -1042,6 +1049,12 @@ Removes an outermost encapsulation from the packet:
> > and NSH inner packet types. Other types raise unsupported packet type
> > errors.
> >
> > + - Otherwise, if the packet is a MPLS packet, removes the MPLS header
> > + and classifies the inner packet as mentioned in the packet type
> > + argument of the decap. The packet_type field specifies the type of
> > + the packet in the format specified in OpenFlow 1.5 chapter
> > + `7.2.3.11 Packet Type Match Field`
>
> And what if the inner packet is not the packet stated in the OF action?
>
It will wrongly classify the inner packet. But this problem should be there for pop_mpls also. MPLS header has no next protocol field.
> > +
> > - Otherwise, raises an unsupported packet type error.
> >
> > **Conformance**
>
> This section needs an update.
>
> > diff --git a/NEWS b/NEWS
> > index 90f4b1590..cac602d09 100644
> > --- a/NEWS
> > +++ b/NEWS
> > @@ -211,7 +211,7 @@ v2.14.0 - 17 Aug 2020
> > - GTP-U Tunnel Protocol
> > * Add two new fields: tun_gtpu_flags, tun_gtpu_msgtype.
> > * Only support for userspace datapath.
> > -
>
> Please, keep the line.
>
> > + - Encap & Decap action support for MPLS packet type.
>
> Please, don't touch release notes for 2.14. Move to Post-2.16.
>
> >
> > v2.13.0 - 14 Feb 2020
> > ---------------------
> > diff --git a/datapath/linux/compat/include/linux/openvswitch.h b/datapath/linux/compat/include/linux/openvswitch.h
> > index f0595eeba..88a653771 100644
> > --- a/datapath/linux/compat/include/linux/openvswitch.h
> > +++ b/datapath/linux/compat/include/linux/openvswitch.h
> > @@ -817,8 +817,32 @@ struct ovs_action_push_tnl {
> > };
> > #endif
> >
> > -/**
> > - * enum ovs_ct_attr - Attributes for %OVS_ACTION_ATTR_CT action.
> > +/* struct ovs_action_add_mpls - %OVS_ACTION_ATTR_ADD_MPLS action
> > + * argument.
> > + * @mpls_lse: MPLS label stack entry to push.
> > + * @mpls_ethertype: Ethertype to set in the encapsulating ethernet frame.
> > + * @tun_flags: MPLS tunnel attributes.
> > + *
> > + * The only values @mpls_ethertype should ever be given are %ETH_P_MPLS_UC and
> > + * %ETH_P_MPLS_MC, indicating MPLS unicast or multicast. Other are rejected.
> > + */
> > +struct ovs_action_add_mpls {
> > + __be32 mpls_lse;
> > + __be16 mpls_ethertype; /* Either %ETH_P_MPLS_UC or %ETH_P_MPLS_MC */
> > + __u16 tun_flags;
> > +};
> > +
> > +#define OVS_MPLS_L3_TUNNEL_FLAG_MASK (1 << 0) /* Flag to specify the place of
> > + * insertion of MPLS header.
> > + * When false, the MPLS header
> > + * will be inserted at the start
> > + * of the packet.
> > + * When true, the MPLS header
> > + * will be inserted at the start
> > + * of the l3 header.
> > + */
> > +
>
> Above code is located in a different place in the kernel header.
> Please move it accordingly.
>
> > +/* enum ovs_ct_attr - Attributes for %OVS_ACTION_ATTR_CT action.
> > * @OVS_CT_ATTR_COMMIT: If present, commits the connection to the conntrack
> > * table. This allows future packets for the same connection to be identified
> > * as 'established' or 'related'. The flow key for the current packet will
> > @@ -1008,6 +1032,10 @@ struct check_pkt_len_arg {
> > * @OVS_ACTION_ATTR_CHECK_PKT_LEN: Check the packet length and execute a set
> > * of actions if greater than the specified packet length, else execute
> > * another set of actions.
> > + * @OVS_ACTION_ATTR_ADD_MPLS: Push a new MPLS label stack entry at the
> > + * start of the packet or at the start of the l3 header depending on the value
> > + * of l3 tunnel flag in the tun_flags field of OVS_ACTION_ATTR_ADD_MPLS
> > + * argument.
> > * @OVS_ACTION_ATTR_DROP: Explicit drop action.
> > */
> >
> > @@ -1037,6 +1065,7 @@ enum ovs_action_attr {
> > OVS_ACTION_ATTR_METER, /* u32 meter number. */
> > OVS_ACTION_ATTR_CLONE, /* Nested OVS_CLONE_ATTR_*. */
> > OVS_ACTION_ATTR_CHECK_PKT_LEN, /* Nested OVS_CHECK_PKT_LEN_ATTR_*. */
> > + OVS_ACTION_ATTR_ADD_MPLS, /* struct ovs_action_add_mpls. */
> >
> > #ifndef __KERNEL__
> > OVS_ACTION_ATTR_TUNNEL_PUSH, /* struct ovs_action_push_tnl*/
> > diff --git a/include/openvswitch/ofp-ed-props.h b/include/openvswitch/ofp-ed-props.h
> > index 306c6fe73..96ef3d951 100644
> > --- a/include/openvswitch/ofp-ed-props.h
> > +++ b/include/openvswitch/ofp-ed-props.h
> > @@ -46,6 +46,11 @@ enum ofp_ed_nsh_prop_type {
> > OFPPPT_PROP_NSH_TLV = 2, /* property TLV in NSH */
> > };
> >
> > +enum ofp_ed_mpls_prop_type {
> > + OFPPPT_PROP_MPLS_NONE = 0, /* unused */
> > + OFPPPT_PROP_MPLS_ETHERTYPE = 1, /* MPLS Ethertype */
> > +};
> > +
> > /*
> > * External representation of encap/decap properties.
> > * These must be padded to a multiple of 8 bytes.
> > @@ -72,6 +77,12 @@ struct ofp_ed_prop_nsh_tlv {
> > uint8_t data[0];
> > };
> >
> > +struct ofp_ed_prop_mpls_ethertype {
> > + struct ofp_ed_prop_header header;
> > + uint16_t ether_type; /* MPLS ethertype . */
> > + uint8_t pad[2]; /* Padding to 8 bytes. */
> > +};
> > +
> > /*
> > * Internal representation of encap/decap properties
> > */
> > @@ -96,6 +107,13 @@ struct ofpact_ed_prop_nsh_tlv {
> > /* tlv_len octets of metadata value, padded to a multiple of 8 bytes. */
> > uint8_t data[0];
> > };
> > +
> > +struct ofpact_ed_prop_mpls_ethertype {
> > + struct ofpact_ed_prop header;
> > + uint16_t ether_type; /* MPLS ethertype . */
> > + uint8_t pad[2]; /* Padding to 8 bytes. */
> > +};
> > +
> > enum ofperr decode_ed_prop(const struct ofp_ed_prop_header **ofp_prop,
> > struct ofpbuf *out, size_t *remaining);
> > enum ofperr encode_ed_prop(const struct ofpact_ed_prop **prop,
> > diff --git a/lib/dpif-netdev.c b/lib/dpif-netdev.c
> > index 75f381ec1..140302a90 100644
> > --- a/lib/dpif-netdev.c
> > +++ b/lib/dpif-netdev.c
> > @@ -8304,6 +8304,7 @@ dp_execute_cb(void *aux_, struct dp_packet_batch *packets_,
> > case OVS_ACTION_ATTR_CT_CLEAR:
> > case OVS_ACTION_ATTR_CHECK_PKT_LEN:
> > case OVS_ACTION_ATTR_DROP:
> > + case OVS_ACTION_ATTR_ADD_MPLS:
> > case __OVS_ACTION_ATTR_MAX:
> > OVS_NOT_REACHED();
> > }
> > diff --git a/lib/dpif.c b/lib/dpif.c
> > index 8c4aed47b..99aba3cae 100644
> > --- a/lib/dpif.c
> > +++ b/lib/dpif.c
> > @@ -1274,6 +1274,7 @@ dpif_execute_helper_cb(void *aux_, struct dp_packet_batch *packets_,
> > case OVS_ACTION_ATTR_UNSPEC:
> > case OVS_ACTION_ATTR_CHECK_PKT_LEN:
> > case OVS_ACTION_ATTR_DROP:
> > + case OVS_ACTION_ATTR_ADD_MPLS:
> > case __OVS_ACTION_ATTR_MAX:
> > OVS_NOT_REACHED();
> > }
> > diff --git a/lib/odp-execute.c b/lib/odp-execute.c
> > index 6eeda2a61..2f4cdd92c 100644
> > --- a/lib/odp-execute.c
> > +++ b/lib/odp-execute.c
> > @@ -819,6 +819,7 @@ requires_datapath_assistance(const struct nlattr *a)
> > case OVS_ACTION_ATTR_POP_NSH:
> > case OVS_ACTION_ATTR_CT_CLEAR:
> > case OVS_ACTION_ATTR_CHECK_PKT_LEN:
> > + case OVS_ACTION_ATTR_ADD_MPLS:
> > case OVS_ACTION_ATTR_DROP:
> > return false;
> >
> > @@ -1061,6 +1062,17 @@ odp_execute_actions(void *dp, struct dp_packet_batch *batch, bool steal,
> > }
> > break;
> >
> > + case OVS_ACTION_ATTR_ADD_MPLS: {
> > + const struct ovs_action_add_mpls *mpls = nl_attr_get(a);
> > + bool l3_flag = mpls->tun_flags & OVS_MPLS_L3_TUNNEL_FLAG_MASK;
> > +
> > + DP_PACKET_BATCH_FOR_EACH (i, packet, batch) {
> > + add_mpls(packet, mpls->mpls_ethertype, mpls->mpls_lse,
> > + l3_flag);
> > + }
> > + break;
> > + }
> > +
> > case OVS_ACTION_ATTR_DROP:{
> > const enum xlate_error *drop_reason = nl_attr_get(a);
> >
> > diff --git a/lib/odp-util.c b/lib/odp-util.c
> > index fbdfc7ad8..709f4f31a 100644
> > --- a/lib/odp-util.c
> > +++ b/lib/odp-util.c
> > @@ -142,6 +142,7 @@ odp_action_len(uint16_t type)
> > case OVS_ACTION_ATTR_PUSH_NSH: return ATTR_LEN_VARIABLE;
> > case OVS_ACTION_ATTR_POP_NSH: return 0;
> > case OVS_ACTION_ATTR_CHECK_PKT_LEN: return ATTR_LEN_VARIABLE;
> > + case OVS_ACTION_ATTR_ADD_MPLS: return sizeof(struct ovs_action_add_mpls);
> > case OVS_ACTION_ATTR_DROP: return sizeof(uint32_t);
> >
> > case OVS_ACTION_ATTR_UNSPEC:
> > @@ -1254,6 +1255,14 @@ format_odp_action(struct ds *ds, const struct nlattr *a,
> > case OVS_ACTION_ATTR_CHECK_PKT_LEN:
> > format_odp_check_pkt_len_action(ds, a, portno_names);
> > break;
> > + case OVS_ACTION_ATTR_ADD_MPLS: {
> > + const struct ovs_action_add_mpls *mpls = nl_attr_get(a);
> > + ds_put_cstr(ds, "add_mpls(");
> > + format_mpls_lse(ds, mpls->mpls_lse);
> > + ds_put_format(ds, ",eth_type=0x%"PRIx16")",
> > + ntohs(mpls->mpls_ethertype));
> > + break;
> > + }
> > case OVS_ACTION_ATTR_DROP:
> > ds_put_cstr(ds, "drop");
> > break;
> > @@ -2595,6 +2604,29 @@ parse_odp_action__(struct parse_odp_context *context, const char *s,
> > return retval;
> > }
> > }
> > + {
> > + struct ovs_action_add_mpls mpls;
> > + uint32_t lse;
> > + uint8_t ttl, tc, bos;
> > + int n = -1;
> > + uint16_t eth_type;
> > +
> > + if (ovs_scan(s,
> > + "add_mpls(label=%"SCNi32",tc=%"SCNd8",ttl=%"SCNd8",bos=%"SCNd8",\
> > + eth_type=0x%"SCNx16")%n", &lse, &tc, &ttl, &bos, ð_type, &n)) {
>
> Please, don't use a line continuation here. Just close the '"' on the
> first line and open a new one on the second.
>
> > +
> > + mpls.mpls_ethertype = htons(eth_type);
> > + mpls.mpls_lse = htonl(lse << MPLS_LABEL_SHIFT |
> > + tc << MPLS_TC_SHIFT |
>
> Nit: Will look nicer with two spaces after 'tc'.
>
> > + ttl << MPLS_TTL_SHIFT |
> > + bos << MPLS_BOS_SHIFT);
> > + mpls.tun_flags = 0;
> > + nl_msg_put_unspec(actions, OVS_ACTION_ATTR_ADD_MPLS,
> > + &mpls, sizeof mpls);
> > +
> > + return n;
> > + }
> > + }
> >
> > {
> > struct ovs_action_push_tnl data;
> > @@ -7890,7 +7922,7 @@ commit_vlan_action(const struct flow* flow, struct flow *base,
> > /* Wildcarding already done at action translation time. */
> > static void
> > commit_mpls_action(const struct flow *flow, struct flow *base,
> > - struct ofpbuf *odp_actions)
> > + struct ofpbuf *odp_actions, bool pending_encap)
> > {
> > int base_n = flow_count_mpls_labels(base, NULL);
> > int flow_n = flow_count_mpls_labels(flow, NULL);
> > @@ -7938,18 +7970,29 @@ commit_mpls_action(const struct flow *flow, struct flow *base,
> > /* If, after the above popping and setting, there are more LSEs in flow
> > * than base then some LSEs need to be pushed. */
> > while (base_n < flow_n) {
> > - struct ovs_action_push_mpls *mpls;
> >
> > - mpls = nl_msg_put_unspec_zero(odp_actions,
> > - OVS_ACTION_ATTR_PUSH_MPLS,
> > - sizeof *mpls);
> > - mpls->mpls_ethertype = flow->dl_type;
> > - mpls->mpls_lse = flow->mpls_lse[flow_n - base_n - 1];
> > + if (pending_encap) {
> > + struct ovs_action_add_mpls *mpls;
> > +
> > + mpls = nl_msg_put_unspec_zero(odp_actions,
> > + OVS_ACTION_ATTR_ADD_MPLS,
> > + sizeof *mpls);
> > + mpls->mpls_ethertype = flow->dl_type;
> > + mpls->mpls_lse = flow->mpls_lse[flow_n - base_n - 1];
> > + } else {
> > + struct ovs_action_push_mpls *mpls;
> > +
> > + mpls = nl_msg_put_unspec_zero(odp_actions,
> > + OVS_ACTION_ATTR_PUSH_MPLS,
> > + sizeof *mpls);
> > + mpls->mpls_ethertype = flow->dl_type;
> > + mpls->mpls_lse = flow->mpls_lse[flow_n - base_n - 1];
> > + }
> > /* Update base flow's MPLS stack, but do not clear L3. We need the L3
> > * headers if the flow is restored later due to returning from a patch
> > * port or group bucket. */
> > - flow_push_mpls(base, base_n, mpls->mpls_ethertype, NULL, false);
> > - flow_set_mpls_lse(base, 0, mpls->mpls_lse);
> > + flow_push_mpls(base, base_n, flow->dl_type, NULL, false);
> > + flow_set_mpls_lse(base, 0, flow->mpls_lse[flow_n - base_n - 1]);
> > base_n++;
> > }
> > }
> > @@ -8600,6 +8643,10 @@ commit_encap_decap_action(const struct flow *flow,
> > memcpy(&base_flow->dl_dst, &flow->dl_dst,
> > sizeof(*flow) - offsetof(struct flow, dl_dst));
> > break;
> > + case PT_MPLS:
> > + commit_mpls_action(flow, base_flow, odp_actions,
> > + pending_encap);
> > + break;
> > default:
> > /* Only the above protocols are supported for encap.
> > * The check is done at action translation. */
> > @@ -8622,6 +8669,10 @@ commit_encap_decap_action(const struct flow *flow,
> > /* pop_nsh. */
> > odp_put_pop_nsh_action(odp_actions);
> > break;
> > + case PT_MPLS:
> > + commit_mpls_action(flow, base_flow, odp_actions,
> > + pending_encap);
> > + break;
> > default:
> > /* Checks are done during translation. */
> > OVS_NOT_REACHED();
> > @@ -8667,7 +8718,7 @@ commit_odp_actions(const struct flow *flow, struct flow *base,
> > /* Make packet a non-MPLS packet before committing L3/4 actions,
> > * which would otherwise do nothing. */
> > if (eth_type_mpls(base->dl_type) && !eth_type_mpls(flow->dl_type)) {
> > - commit_mpls_action(flow, base, odp_actions);
> > + commit_mpls_action(flow, base, odp_actions, false);
> > mpls_done = true;
> > }
> > commit_set_nsh_action(flow, base, odp_actions, wc, use_masked);
> > @@ -8675,7 +8726,7 @@ commit_odp_actions(const struct flow *flow, struct flow *base,
> > commit_set_port_action(flow, base, odp_actions, wc, use_masked);
> > slow2 = commit_set_icmp_action(flow, base, odp_actions, wc);
> > if (!mpls_done) {
> > - commit_mpls_action(flow, base, odp_actions);
> > + commit_mpls_action(flow, base, odp_actions, false);
> > }
> > commit_vlan_action(flow, base, odp_actions, wc);
> > commit_set_priority_action(flow, base, odp_actions, wc, use_masked);
> > diff --git a/lib/ofp-actions.c b/lib/ofp-actions.c
> > index ecf914eac..8b74386b1 100644
> > --- a/lib/ofp-actions.c
> > +++ b/lib/ofp-actions.c
> > @@ -4468,6 +4468,7 @@ decode_NXAST_RAW_ENCAP(const struct nx_action_encap *nae,
> > switch (ntohl(nae->new_pkt_type)) {
> > case PT_ETH:
> > case PT_NSH:
> > + case PT_MPLS:
> > /* Add supported encap header types here. */
> > break;
> > default:
> > @@ -4519,6 +4520,8 @@ parse_encap_header(const char *hdr, ovs_be32 *packet_type)
> > *packet_type = htonl(PT_ETH);
> > } else if (strcmp(hdr, "nsh") == 0) {
> > *packet_type = htonl(PT_NSH);
> > + } else if (strcmp(hdr, "mpls") == 0) {
> > + *packet_type = htonl(PT_MPLS);
> > } else {
> > return false;
> > }
> > @@ -4600,6 +4603,8 @@ format_encap_pkt_type(const ovs_be32 pkt_type)
> > return "ethernet";
> > case PT_NSH:
> > return "nsh";
> > + case PT_MPLS:
> > + return "mpls";
> > default:
> > return "UNKNOWN";
> > }
> > diff --git a/lib/ofp-ed-props.c b/lib/ofp-ed-props.c
> > index 02a9235d5..14dfbae1e 100644
> > --- a/lib/ofp-ed-props.c
> > +++ b/lib/ofp-ed-props.c
> > @@ -79,6 +79,27 @@ decode_ed_prop(const struct ofp_ed_prop_header **ofp_prop,
> > }
> > break;
> > }
> > + case OFPPPC_MPLS: {
> > + switch (prop_type) {
> > + case OFPPPT_PROP_MPLS_ETHERTYPE: {
> > + struct ofp_ed_prop_mpls_ethertype *opmet =
> > + ALIGNED_CAST(struct ofp_ed_prop_mpls_ethertype *, *ofp_prop);
> > + if (len > sizeof(*opmet) || len > *remaining) {
>
> Please, don't parethesize the argument of a sizeof. I know that
> code in this file does that a lot, but it's not a reson to folow
> a bad pattern. Some for other places in this file.
>
> No need to touch existing code, but the new code should follow
> the coding style.
>
> > + return OFPERR_NXBAC_BAD_ED_PROP;
> > + }
> > + struct ofpact_ed_prop_mpls_ethertype *pmet =
> > + ofpbuf_put_uninit(out, sizeof(*pmet));
>
> This structure contains an uninitialized padding. Later the
> ofpact will be compared with memcmp causing incorect behavior.
> Please, use ofpbuf_put_zero() here. See the following commit
> for an example of other places that needs to be fixed:
>
> 51dec40f8e9d ("ofp-ed-props: Fix using uninitialized padding for NSH encap actions.")
>
> Also, since you're adding a new OF action, please add a test
> to tests/ofp-actions.at. Again, see the example of such a test
> in the commit above.
>
> > + pmet->header.prop_class = prop_class;
> > + pmet->header.type = prop_type;
> > + pmet->header.len = len;
> > + pmet->ether_type = opmet->ether_type;
> > + break;
> > + }
> > + default:
> > + return OFPERR_NXBAC_UNKNOWN_ED_PROP;
> > + }
> > + break;
> > + }
> > default:
> > return OFPERR_NXBAC_UNKNOWN_ED_PROP;
> > }
> > @@ -134,6 +155,26 @@ encode_ed_prop(const struct ofpact_ed_prop **prop,
> > }
> > break;
> > }
> > + case OFPPPC_MPLS: {
> > + switch ((*prop)->type) {
> > + case OFPPPT_PROP_MPLS_ETHERTYPE: {
> > + struct ofpact_ed_prop_mpls_ethertype *pmet =
> > + ALIGNED_CAST(struct ofpact_ed_prop_mpls_ethertype *, *prop);
> > + struct ofp_ed_prop_mpls_ethertype *opmet =
> > + ofpbuf_put_uninit(out, sizeof(*opmet));
> > + opmet->header.prop_class = htons((*prop)->prop_class);
> > + opmet->header.type = (*prop)->type;
> > + opmet->header.len =
> > + offsetof(struct ofpact_ed_prop_mpls_ethertype, pad);
> > + opmet->ether_type = pmet->ether_type;
> > + prop_len = sizeof(*pmet);
> > + break;
> > + }
> > + default:
> > + return OFPERR_OFPBAC_BAD_ARGUMENT;
> > + }
> > + break;
> > + }
> > default:
> > return OFPERR_OFPBAC_BAD_ARGUMENT;
> > }
> > @@ -181,6 +222,13 @@ parse_ed_prop_type(uint16_t prop_class,
> > } else {
> > return false;
> > }
> > + case OFPPPC_MPLS:
> > + if (!strcmp(str, "ether_type")) {
> > + *type = OFPPPT_PROP_MPLS_ETHERTYPE;
> > + return true;
> > + } else {
> > + return false;
> > + }
> > default:
> > return false;
> > }
> > @@ -259,6 +307,29 @@ parse_ed_prop_value(uint16_t prop_class, uint8_t prop_type OVS_UNUSED,
> > OVS_NOT_REACHED();
> > }
> > break;
> > + case OFPPPC_MPLS:
> > + switch (prop_type) {
> > + case OFPPPT_PROP_MPLS_ETHERTYPE: {
> > + uint16_t ethertype;
> > + error = str_to_u16(value, "ether_type", ðertype);
> > + if (error != NULL) {
> > + return error;
> > + }
> > + struct ofpact_ed_prop_mpls_ethertype *pmet =
> > + ofpbuf_put_uninit(out, sizeof(*pmet));
> > + pmet->header.prop_class = prop_class;
> > + pmet->header.type = prop_type;
> > + pmet->header.len =
> > + offsetof(struct ofpact_ed_prop_mpls_ethertype, pad);
> > + pmet->ether_type = ethertype;
> > +
> > + break;
> > + }
> > + default:
> > + /* Unsupported property types rejected before. */
> > + OVS_NOT_REACHED();
> > + }
> > + break;
> > default:
> > /* Unsupported property classes rejected before. */
> > OVS_NOT_REACHED();
> > @@ -300,6 +371,14 @@ format_ed_prop_type(const struct ofpact_ed_prop *prop)
> > OVS_NOT_REACHED();
> > }
> > break;
> > + case OFPPPC_MPLS:
> > + switch (prop->type) {
> > + case OFPPPT_PROP_MPLS_ETHERTYPE:
> > + return "ether_type";
> > + default:
> > + OVS_NOT_REACHED();
> > + }
> > + break;
> > default:
> > OVS_NOT_REACHED();
> > }
> > @@ -332,6 +411,18 @@ format_ed_prop(struct ds *s OVS_UNUSED,
> > default:
> > OVS_NOT_REACHED();
> > }
> > + case OFPPPC_MPLS:
> > + switch (prop->type) {
> > + case OFPPPT_PROP_MPLS_ETHERTYPE: {
> > + struct ofpact_ed_prop_mpls_ethertype *pmet =
> > + ALIGNED_CAST(struct ofpact_ed_prop_mpls_ethertype *, prop);
> > + ds_put_format(s, "%s=%d", format_ed_prop_type(prop),
> > + pmet->ether_type);
> > + return;
> > + }
> > + default:
> > + OVS_NOT_REACHED();
> > + }
> > default:
> > OVS_NOT_REACHED();
> > }
> > diff --git a/lib/packets.c b/lib/packets.c
> > index 4a7643c5d..d373e1580 100644
> > --- a/lib/packets.c
> > +++ b/lib/packets.c
> > @@ -418,6 +418,39 @@ push_mpls(struct dp_packet *packet, ovs_be16 ethtype, ovs_be32 lse)
> > pkt_metadata_init_conn(&packet->md);
> > }
> >
> > +void
> > +add_mpls(struct dp_packet *packet, ovs_be16 ethtype, ovs_be32 lse,
> > + bool l3_encap)
> > +{
> > + if (!eth_type_mpls(ethtype)) {
> > + return;
> > + }
> > +
> > + if (!l3_encap) {
> > + ovs_be32 *header = dp_packet_push_uninit(packet, MPLS_HLEN);
> > +
> > + *header = lse;
> > + packet->l2_5_ofs = 0;
> > + packet->packet_type = htonl(PT_MPLS);
> > + } else {
> > + size_t len;
> > + char *header;
> > +
> > + if (!is_mpls(packet)) {
> > + /* Set MPLS label stack offset. */
> > + packet->l2_5_ofs = packet->l3_ofs;
> > + }
> > + set_ethertype(packet, ethtype);
> > +
> > + /* Push new MPLS shim header onto packet. */
> > + len = packet->l2_5_ofs;
> > + header = dp_packet_resize_l2_5(packet, MPLS_HLEN);
> > + memmove(header, header + MPLS_HLEN, len);
> > + memcpy(header + len, &lse, sizeof lse);
> > + }
> > + pkt_metadata_init_conn(&packet->md);
> > +}
> > +
> > /* If 'packet' is an MPLS packet, removes its outermost MPLS label stack entry.
> > * If the label that was removed was the only MPLS label, changes 'packet''s
> > * Ethertype to 'ethtype' (which ordinarily should not be an MPLS
> > @@ -440,6 +473,18 @@ pop_mpls(struct dp_packet *packet, ovs_be16 ethtype)
> > /* Invalidate offload flags as they are not valid after
> > * decapsulation of MPLS header. */
> > dp_packet_reset_offload(packet);
> > +
> > + /* packet_type must be reset for the MPLS packets with no l2 header */
> > + if (!len) {
> > + if (ethtype == htons(ETH_TYPE_TEB)) {
> > + /* The inner packet must be classsified as ethernet if the
> > + * ethtype is ETH_TYPE_TEB. */
> > + packet->packet_type = htonl(PT_ETH);
> > + } else {
> > + packet->packet_type = PACKET_TYPE_BE(OFPHTN_ETHERTYPE,
> > + ntohs(ethtype));
>
> Nit: Please, shift above line one space to the left.
>
> > + }
> > + }
> > }
> > }
> >
> > diff --git a/lib/packets.h b/lib/packets.h
> > index 515bb59b1..f522492b1 100644
> > --- a/lib/packets.h
> > +++ b/lib/packets.h
> > @@ -356,6 +356,8 @@ void set_mpls_lse_label(ovs_be32 *lse, ovs_be32 label);
> > void set_mpls_lse_bos(ovs_be32 *lse, uint8_t bos);
> > ovs_be32 set_mpls_lse_values(uint8_t ttl, uint8_t tc, uint8_t bos,
> > ovs_be32 label);
> > +void add_mpls(struct dp_packet *packet, ovs_be16 ethtype, ovs_be32 lse,
> > + bool l3_encap);
> >
> > /* Example:
> > *
> > diff --git a/ofproto/ofproto-dpif-ipfix.c b/ofproto/ofproto-dpif-ipfix.c
> > index 796eb6f88..9280e008e 100644
> > --- a/ofproto/ofproto-dpif-ipfix.c
> > +++ b/ofproto/ofproto-dpif-ipfix.c
> > @@ -3018,6 +3018,7 @@ dpif_ipfix_read_actions(const struct flow *flow,
> > case OVS_ACTION_ATTR_CHECK_PKT_LEN:
> > case OVS_ACTION_ATTR_UNSPEC:
> > case OVS_ACTION_ATTR_DROP:
> > + case OVS_ACTION_ATTR_ADD_MPLS:
> > case __OVS_ACTION_ATTR_MAX:
> > default:
> > break;
> > diff --git a/ofproto/ofproto-dpif-sflow.c b/ofproto/ofproto-dpif-sflow.c
> > index 864c136b5..30e7caf54 100644
> > --- a/ofproto/ofproto-dpif-sflow.c
> > +++ b/ofproto/ofproto-dpif-sflow.c
> > @@ -1226,6 +1226,7 @@ dpif_sflow_read_actions(const struct flow *flow,
> > case OVS_ACTION_ATTR_UNSPEC:
> > case OVS_ACTION_ATTR_CHECK_PKT_LEN:
> > case OVS_ACTION_ATTR_DROP:
> > + case OVS_ACTION_ATTR_ADD_MPLS:
> > case __OVS_ACTION_ATTR_MAX:
> > default:
> > break;
> > diff --git a/ofproto/ofproto-dpif-xlate.c b/ofproto/ofproto-dpif-xlate.c
> > index 8723cb4e8..0f68e281f 100644
> > --- a/ofproto/ofproto-dpif-xlate.c
> > +++ b/ofproto/ofproto-dpif-xlate.c
> > @@ -6404,6 +6404,54 @@ rewrite_flow_encap_ethernet(struct xlate_ctx *ctx,
> > }
> > }
> >
> > +static void
> > +rewrite_flow_encap_mpls(struct xlate_ctx *ctx,
> > + const struct ofpact_encap *encap,
> > + struct flow *flow,
> > + struct flow_wildcards *wc)
> > +{
> > + int n;
> > + uint32_t i;
> > + uint16_t ether_type;
> > + const char *ptr = (char *) encap->props;
>
> Reverse xmas tree, please. :)
>
> And is it necessary to cast to 'char *' here?
>
> > +
> > + for (i = 0; i < encap->n_props; i++) {
> > + struct ofpact_ed_prop *prop_ptr =
> > + ALIGNED_CAST(struct ofpact_ed_prop *, ptr);
> > + if (prop_ptr->prop_class == OFPPPC_MPLS) {
> > + switch (prop_ptr->type) {
> > + case OFPPPT_PROP_MPLS_ETHERTYPE: {
> > + struct ofpact_ed_prop_mpls_ethertype *prop_ether_type =
> > + ALIGNED_CAST(struct ofpact_ed_prop_mpls_ethertype *,
> > + prop_ptr);
> > + ether_type = prop_ether_type->ether_type;
> > + break;
> > + }
> > + }
> > + }
>
> You're not advancing the 'ptr' here checking the same data.
> Please, add a unit test for this scenario. It's not obvious,
> how this should work.
>
It will not work. I have tested only with n_props=1 and hence it worked for me.
I took the implementation from NSH and didn’t adapt it correctly. I will rework this part.
For MPLS, n_props always has to be 1.
I will add a check for n_props=1 in parse_ENCAP for OFPPPC_MPLS prop_class.
I Will leave a error message “Invalid Argument” if n_prop!=1.
> > + }
> > +
> > + wc->masks.packet_type = OVS_BE32_MAX;
> > +
> > + /* If the current packet is already a MPLS packet with ethernet header the
> > + * existing MPLS states must be cleared before the encap MPLS action is
> > + * applied */
>
> Period at the end of a comment.
>
> > + if (flow->packet_type == htonl(PT_ETH) &&
> > + flow->dl_type == htons(ETH_TYPE_MPLS)) {
> > + memset(&ctx->wc->masks.mpls_lse, 0x0,
> > + sizeof *wc->masks.mpls_lse * FLOW_MAX_MPLS_LABELS);
> > + memset(&flow->mpls_lse, 0x0, sizeof *flow->mpls_lse *
> > + FLOW_MAX_MPLS_LABELS);
> > + memset(&ctx->base_flow.mpls_lse, 0x0, sizeof *ctx->base_flow.mpls_lse *
> > + FLOW_MAX_MPLS_LABELS);
> > + }
> > + flow->packet_type = htonl(PT_MPLS);
> > + n = flow_count_mpls_labels(flow, ctx->wc);
> > + flow_push_mpls(flow, n, htons(ether_type), ctx->wc, true);
>
> I suppose, flow_push_mpls() will crash if n > FLOW_MAX_MPLS_LABELS.
> Should we check and stop processing in this case with
> XLATE_TOO_MANY_MPLS_LABELS ?
>
> Unit test for this would be great too.
>
> > + flow->dl_src = eth_addr_zero;
> > + flow->dl_dst = eth_addr_zero;
> > +}
> > +
> > /* For an MD2 NSH header returns a pointer to an ofpbuf with the encoded
> > * MD2 TLVs provided as encap properties to the encap operation. This
> > * will be stored as encap_data in the ctx and copied into the push_nsh
> > @@ -6535,6 +6583,12 @@ xlate_generic_encap_action(struct xlate_ctx *ctx,
> > case PT_NSH:
> > encap_data = rewrite_flow_push_nsh(ctx, encap, flow, wc);
> > break;
> > + case PT_MPLS:
> > + rewrite_flow_encap_mpls(ctx, encap, flow, wc);
> > + if (!ctx->xbridge->support.add_mpls) {
> > + ctx->xout->slow |= SLOW_ACTION;
> > + }
> > + break;
> > default:
> > /* New packet type was checked during decoding. */
> > OVS_NOT_REACHED();
> > @@ -6606,6 +6660,30 @@ xlate_generic_decap_action(struct xlate_ctx *ctx,
> > ctx->pending_decap = true;
> > /* Trigger recirculation. */
> > return true;
> > + case PT_MPLS: {
> > + int n;
> > + ovs_be16 ethertype;
> > +
> > + flow->packet_type = decap->new_pkt_type;
> > + ethertype = pt_ns_type_be(flow->packet_type);
> > +
> > + n = flow_count_mpls_labels(flow, ctx->wc);
> > + if (!ethertype) {
> > + ethertype = htons(ETH_TYPE_TEB);
> > + }
> > + flow_pop_mpls(flow, n, ethertype, ctx->wc);
>
> Repeating myself, but what happens if the inner packet actually has a
> different packet type than one specified in the OF rule?
>
> > +
> > + if (!ctx->xbridge->support.add_mpls) {
> > + ctx->xout->slow |= SLOW_ACTION;
> > + }
> > + ctx->pending_decap = true;
> > + if (n == 1) {
> > + /* Trigger recirculation. */
> > + return true;
> > + } else {
> > + return false;
> > + }
> > + }
> > default:
> > /* Error handling: drop packet. */
> > xlate_report_debug(
> > diff --git a/ofproto/ofproto-dpif.c b/ofproto/ofproto-dpif.c
> > index cba49a99e..c65b992a7 100644
> > --- a/ofproto/ofproto-dpif.c
> > +++ b/ofproto/ofproto-dpif.c
> > @@ -1538,6 +1538,42 @@ check_nd_extensions(struct dpif_backer *backer)
> >
> > return !error;
> > }
> > +/* Tests whether 'backer''s datapath supports the
> > + * OVS_ACTION_ATTR_ADD_MPLS action. */
> > +static bool
> > +check_add_mpls(struct dpif_backer *backer)
> > +{
> > + struct odputil_keybuf keybuf;
> > + struct ofpbuf actions;
> > + struct ofpbuf key;
> > + struct flow flow;
> > + bool supported;
> > +
> > + struct odp_flow_key_parms odp_parms = {
> > + .flow = &flow,
> > + .probe = true,
> > + };
> > +
> > + memset(&flow, 0, sizeof flow);
> > + ofpbuf_use_stack(&key, &keybuf, sizeof keybuf);
> > + odp_flow_key_from_flow(&odp_parms, &key);
> > + ofpbuf_init(&actions, 64);
> > +
> > + struct ovs_action_add_mpls *mpls;
> > +
> > + mpls = nl_msg_put_unspec_zero(&actions,
> > + OVS_ACTION_ATTR_ADD_MPLS,
> > + sizeof *mpls);
> > + mpls->mpls_ethertype = htons(ETH_TYPE_MPLS);
> > +
> > + supported = dpif_probe_feature(backer->dpif, "add_mpls", &key,
> > + &actions, NULL);
> > + ofpbuf_uninit(&actions);
> > + VLOG_INFO("%s: Datapath %s add_mpls action",
> > + dpif_name(backer->dpif),
> > + supported ? "supports" : "does not support");
> > + return supported;
> > +}
> >
> > #define CHECK_FEATURE__(NAME, SUPPORT, FIELD, VALUE, ETHTYPE) \
> > static bool \
> > @@ -1609,6 +1645,7 @@ check_support(struct dpif_backer *backer)
> > backer->rt_support.lb_output_action =
> > dpif_supports_lb_output_action(backer->dpif);
> > backer->rt_support.ct_zero_snat = dpif_supports_ct_zero_snat(backer);
> > + backer->rt_support.add_mpls = check_add_mpls(backer);
> >
> > /* Flow fields. */
> > backer->rt_support.odp.ct_state = check_ct_state(backer);
> > @@ -5625,6 +5662,7 @@ get_datapath_cap(const char *datapath_type, struct smap *cap)
> > s.explicit_drop_action ? "true" :"false");
> > smap_add(cap, "lb_output_action", s.lb_output_action ? "true" : "false");
> > smap_add(cap, "ct_zero_snat", s.ct_zero_snat ? "true" : "false");
> > + smap_add(cap, "add_mpls", s.add_mpls ? "true" : "false");
> > }
> >
> > /* Gets timeout policy name in 'backer' based on 'zone', 'dl_type' and
> > diff --git a/ofproto/ofproto-dpif.h b/ofproto/ofproto-dpif.h
> > index 191cfcb0d..a83cc42a9 100644
> > --- a/ofproto/ofproto-dpif.h
> > +++ b/ofproto/ofproto-dpif.h
> > @@ -207,7 +207,9 @@ struct group_dpif *group_dpif_lookup(struct ofproto_dpif *,
> > DPIF_SUPPORT_FIELD(bool, lb_output_action, "Optimized Balance TCP mode")\
> > \
> > /* True if the datapath supports all-zero IP SNAT. */ \
> > - DPIF_SUPPORT_FIELD(bool, ct_zero_snat, "Conntrack all-zero IP SNAT")
> > + DPIF_SUPPORT_FIELD(bool, ct_zero_snat, "Conntrack all-zero IP SNAT") \
> > + /* True if the datapath supports add_mpls action */ \
> > + DPIF_SUPPORT_FIELD(bool, add_mpls, "MPLS Label add")
> >
> >
> > /* Stores the various features which the corresponding backer supports. */
> > diff --git a/tests/mpls-xlate.at b/tests/mpls-xlate.at
> > index aafa89ba6..eada8501c 100644
> > --- a/tests/mpls-xlate.at
> > +++ b/tests/mpls-xlate.at
> > @@ -207,3 +207,60 @@ AT_CHECK([tail -1 stdout], [0],
> >
> > OVS_VSWITCHD_STOP
> > AT_CLEANUP
> > +
> > +AT_SETUP([Encap Decap MPLS xlate action])
> > +
> > +OVS_VSWITCHD_START(
> > + [add-port br0 p1 -- set Interface p1 type=dummy ofport_request=1 -- \
> > + add-port br0 p2 -- set Interface p2 type=patch \
> > + options:peer=p3 ofport_request=2 -- \
> > + add-br br1 -- \
> > + set bridge br1 other-config:hwaddr=aa:66:aa:66:00:00 -- \
> > + set bridge br1 datapath-type=dummy other-config:datapath-id=1234 \
> > + fail-mode=secure -- \
> > + add-port br1 p3 -- set Interface p3 type=patch \
> > + options:peer=p2 ofport_request=3 -- \
> > + add-port br1 p4 -- set Interface p4 type=dummy ofport_request=4])
> > +
> > +AT_CHECK([ovs-appctl dpif/show], [0], [dnl
> > +dummy at ovs-dummy: hit:0 missed:0
> > + br0:
> > + br0 65534/100: (dummy-internal)
> > + p1 1/1: (dummy)
> > + p2 2/none: (patch: peer=p3)
> > + br1:
> > + br1 65534/101: (dummy-internal)
> > + p3 3/none: (patch: peer=p2)
> > + p4 4/4: (dummy)
> > +])
> > +
> > +AT_CHECK([ovs-ofctl del-flows br0])
> > +AT_CHECK([ovs-ofctl -O OpenFlow13 add-flow br0 "in_port=p1,actions=encap(mpls(ether_type=0x8847)),encap(ethernet),set_field:00:00:00:00:00:02->dl_dst,set_field:00:00:00:00:00:01->dl_src,output:p2"])
> > +AT_CHECK([ovs-ofctl -O OpenFlow13 add-flow br1 "in_port=p3,dl_type=0x8847 actions=decap(),decap(packet_type(ns=0,type=0)),output:p4"])
> > +
> > +# Now send two real ICMP echo request packets in on port p1
> > +
> > +AT_CHECK([ovs-appctl netdev-dummy/receive p1 1e2ce92a669e3a6dd2099cab0800450000548a53400040011addc0a80a0ac0a80a1e08006f200a4d0001fc509a58000000002715020000000000101112131415161718191a1b1c1d1e1f202122232425262728292a2b2c2d2e2f3031323334353637] ,[0], [ignore])
> > +
> > +AT_CHECK([ovs-appctl netdev-dummy/receive p1 1e2ce92a669e3a6dd2099cab0800450000548a53400040011addc0a80a0ac0a80a1e08006f200a4d0001fc509a58000000002715020000000000101112131415161718191a1b1c1d1e1f202122232425262728292a2b2c2d2e2f3031323334353637] ,[0], [ignore])
> > +
> > +AT_CHECK([ovs-appctl dpctl/dump-flows dummy at ovs-dummy | strip_used | grep -v ipv6 |sort], [0],
> > +[flow-dump from the main thread:
> > +recirc_id(0),in_port(1),packet_type(ns=0,id=0),eth(src=3a:6d:d2:09:9c:ab,dst=1e:2c:e9:2a:66:9e),eth_type(0x0800),ipv4(frag=no), packets:1, bytes:98, used:0.0s, actions:add_mpls(label=0,tc=0,ttl=64,bos=1,eth_type=0x8847),push_eth(src=00:00:00:00:00:01,dst=00:00:00:00:00:02),pop_eth,pop_mpls(eth_type=0x6558),recirc(0x1)
> > +recirc_id(0x1),in_port(1),packet_type(ns=0,id=0),eth_type(0x0800),ipv4(frag=no), packets:1, bytes:98, used:0.0s, actions:4
> > +])
> > +
> > +AT_CHECK(ovs-appctl dpif/set-dp-features br0 add_mpls false)
> > +
> > +AT_CHECK([ovs-appctl netdev-dummy/receive p1 1e2ce92a669e3a6dd2099cab0800450000548a53400040011addc0a80a0ac0a80a1e08006f200a4d0001fc509a58000000002715020000000000101112131415161718191a1b1c1d1e1f202122232425262728292a2b2c2d2e2f3031323334353637] ,[0], [ignore])
> > +
> > +AT_CHECK([ovs-appctl netdev-dummy/receive p1 1e2ce92a669e3a6dd2099cab0800450000548a53400040011addc0a80a0ac0a80a1e08006f200a4d0001fc509a58000000002715020000000000101112131415161718191a1b1c1d1e1f202122232425262728292a2b2c2d2e2f3031323334353637] ,[0], [ignore])
> > +
> > +AT_CHECK([ovs-appctl dpctl/dump-flows dummy at ovs-dummy | strip_used | grep -v ipv6 |sort], [0],
> > +[flow-dump from the main thread:
> > +recirc_id(0),in_port(1),packet_type(ns=0,id=0),eth(src=3a:6d:d2:09:9c:ab,dst=1e:2c:e9:2a:66:9e),eth_type(0x0800),ipv4(frag=no), packets:1, bytes:98, used:0.0s, actions:userspace(pid=0,slow_path(action))
> > +recirc_id(0x2),in_port(1),packet_type(ns=0,id=0),eth_type(0x0800),ipv4(frag=no), packets:1, bytes:98, used:0.0s, actions:4
> > +])
> > +
> > +OVS_VSWITCHD_STOP
> > +AT_CLEANUP
> > diff --git a/tests/odp.at b/tests/odp.at
> > index 07a5cfe39..4d08c59ca 100644
> > --- a/tests/odp.at
> > +++ b/tests/odp.at
> > @@ -384,6 +384,7 @@ check_pkt_len(size=200,gt(drop),le(5))
> > check_pkt_len(size=200,gt(ct(nat)),le(drop))
> > check_pkt_len(size=200,gt(set(eth(src=00:01:02:03:04:05,dst=10:11:12:13:14:15))),le(set(eth(src=00:01:02:03:04:06,dst=10:11:12:13:14:16))))
> > lb_output(1)
> > +add_mpls(label=200,tc=7,ttl=64,bos=1,eth_type=0x8847)
> > ])
> > AT_CHECK_UNQUOTED([ovstest test-odp parse-actions < actions.txt], [0],
> > [`cat actions.txt`
> > diff --git a/tests/system-traffic.at b/tests/system-traffic.at
> > index c4442c183..ee7120ed5 100644
> > --- a/tests/system-traffic.at
> > +++ b/tests/system-traffic.at
> > @@ -1087,6 +1087,314 @@ NS_CHECK_EXEC([at_ns1], [ping -q -c 3 -i 0.3 -w 2 10.1.1.1 | FORMAT_PING], [0],
> > OVS_TRAFFIC_VSWITCHD_STOP
> > AT_CLEANUP
> >
> > +AT_SETUP([mpls - encap header dp-support])
> > +OVS_TRAFFIC_VSWITCHD_START()
> > +
> > +AT_SKIP_IF([! ovs-appctl dpif/show-dp-features br0 2>&1 | grep "MPLS Label add: Yes" >/dev/null])
>
> AT_SKIP_IF([test $HAVE_TCPDUMP = no])
>
> Smae for other tests that use tcpdump.
>
> > +
> > +ADD_NAMESPACES(at_ns0, at_ns1)
> > +
> > +ADD_VETH(p0, at_ns0, br0, "10.1.1.1/24", 36:b1:ee:7c:01:03)
> > +ADD_VETH(p1, at_ns1, br0, "10.1.1.2/24", 36:b1:ee:7c:01:02)
> > +
> > +dnl The flow will encap a mpls header to the ip packet
> > +dnl eth/ip/icmp --> OVS --> eth/mpls/eth/ip/icmp
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flow br0 "table=0,priority=100,dl_type=0x0800 actions=encap(mpls(ether_type=0x8847)),set_mpls_label:2,encap(ethernet),set_field:00:00:00:00:00:02->dl_dst,set_field:00:00:00:00:00:01->dl_src,ovs-p1"])
> > +
> > +rm -rf p1.pcap
> > +NS_CHECK_EXEC([at_ns1], [tcpdump -l -n -xx -U -i p1 > p1.pcap &])
> > +sleep 1
> > +
> > +dnl The hex dump is a icmp packet. pkt=eth/ip/icmp
> > +dnl The packet is sent from p0(at_ns0) interface directed to
> > +dnl p1(at_ns1) interface
> > +NS_CHECK_EXEC([at_ns0], [$PYTHON3 $srcdir/sendpkt.py p0 36 b1 ee 7c 01 02 36 b1 ee 7c 01 03 08 00 45 00 00 54 03 44 40 00 40 01 21 61 0a 01 01 01 0a 01 01 02 08 00 ef ac 7c e4 00 03 5b 2c 1f 61 00 00 00 00 50 0b 02 00 00 00 00 00 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 > /dev/null])
> > +
> > +dnl Check the expected mpls encapsulated packet on the egress interface
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0000: *0000 *0000 *0002 *0000 *0000 *0001 *8847 *0000" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0010: *2140 *36b1 *ee7c *0102 *36b1 *ee7c *0103 *0800" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0020: *4500 *0054 *0344 *4000 *4001 *2161 *0a01 *0101" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0030: *0a01 *0102 *0800 *efac *7ce4 *0003 *5b2c *1f61" 2>&1 1>/dev/null])
> > +
> > +OVS_TRAFFIC_VSWITCHD_STOP
> > +AT_CLEANUP
> > +
> > +AT_SETUP([mpls - encap header slow-path])
> > +OVS_TRAFFIC_VSWITCHD_START()
> > +
> > +AT_CHECK(ovs-appctl dpif/set-dp-features br0 add_mpls false)
> > +ADD_NAMESPACES(at_ns0, at_ns1)
> > +
> > +ADD_VETH(p0, at_ns0, br0, "10.1.1.1/24", 36:b1:ee:7c:01:03)
> > +ADD_VETH(p1, at_ns1, br0, "10.1.1.2/24", 36:b1:ee:7c:01:02)
> > +
> > +dnl The flow will encap a mpls header to the ip packet
> > +dnl eth/ip/icmp --> OVS --> eth/mpls/eth/ip/icmp
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flow br0 "table=0,priority=100,dl_type=0x0800 actions=encap(mpls(ether_type=0x8847)),set_mpls_label:2,encap(ethernet),set_field:00:00:00:00:00:02->dl_dst,set_field:00:00:00:00:00:01->dl_src,ovs-p1"])
> > +
> > +rm -rf p1.pcap
> > +NS_CHECK_EXEC([at_ns1], [tcpdump -l -n -xx -U -i p1 > p1.pcap &])
> > +sleep 1
> > +
> > +dnl The hex dump is a icmp packet. pkt=eth/ip/icmp
> > +dnl The packet is sent from p0(at_ns0) interface directed to
> > +dnl p1(at_ns1) interface
> > +NS_CHECK_EXEC([at_ns0], [$PYTHON3 $srcdir/sendpkt.py p0 36 b1 ee 7c 01 02 36 b1 ee 7c 01 03 08 00 45 00 00 54 03 44 40 00 40 01 21 61 0a 01 01 01 0a 01 01 02 08 00 ef ac 7c e4 00 03 5b 2c 1f 61 00 00 00 00 50 0b 02 00 00 00 00 00 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 > /dev/null])
> > +
> > +dnl Check the expected mpls encapsulated packet on the egress interface
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0000: *0000 *0000 *0002 *0000 *0000 *0001 *8847 *0000" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0010: *2140 *36b1 *ee7c *0102 *36b1 *ee7c *0103 *0800" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0020: *4500 *0054 *0344 *4000 *4001 *2161 *0a01 *0101" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0030: *0a01 *0102 *0800 *efac *7ce4 *0003 *5b2c *1f61" 2>&1 1>/dev/null])
> > +
> > +OVS_TRAFFIC_VSWITCHD_STOP
> > +AT_CLEANUP
> > +
> > +
> > +AT_SETUP([mpls - decap header dp-support])
> > +OVS_TRAFFIC_VSWITCHD_START()
> > +
> > +AT_SKIP_IF([! ovs-appctl dpif/show-dp-features br0 2>&1 | grep "MPLS Label add: Yes" >/dev/null])
> > +
> > +ADD_NAMESPACES(at_ns0, at_ns1)
> > +
> > +ADD_VETH(p0, at_ns0, br0, "10.1.1.1/24", 36:b1:ee:7c:01:03)
> > +ADD_VETH(p1, at_ns1, br0, "10.1.1.2/24", 36:b1:ee:7c:01:02)
> > +
> > +dnl The flow will decap a mpls header which in turn carries a icmp packet
> > +dnl eth/mpls/eth/ip/icmp --> OVS --> eth/ip/icmp
> > +
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flow br0 "table=0,priority=100,dl_type=0x8847,mpls_label=2 actions=decap(),decap(packet_type(ns=0,type=0)),ovs-p1"])
> > +
> > +rm -rf p1.pcap
> > +NS_CHECK_EXEC([at_ns1], [tcpdump -l -n -xx -U -i p1 > p1.pcap &])
> > +sleep 1
> > +
> > +dnl The hex dump is an mpls packet encapsulating ethernet packet. pkt=eth/mpls/eth/ip/icmp
> > +dnl The packet is sent from p0(at_ns0) interface directed to
> > +dnl p1(at_ns1) interface
> > +NS_CHECK_EXEC([at_ns0], [$PYTHON3 $srcdir/sendpkt.py p0 00 00 00 00 00 02 00 00 00 00 00 01 88 47 00 00 21 40 36 b1 ee 7c 01 02 36 b1 ee 7c 01 03 08 00 45 00 00 54 03 44 40 00 40 01 21 61 0a 01 01 01 0a 01 01 02 08 00 ef ac 7c e4 00 03 5b 2c 1f 61 00 00 00 00 50 0b 02 00 00 00 00 00 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 > /dev/null])
> > +
> > +dnl Check the expected decapsulated on the egress interface
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0000: *36b1 *ee7c *0102 *36b1 *ee7c *0103 *0800 *4500" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0010: *0054 *0344 *4000 *4001 *2161 *0a01 *0101 *0a01" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0020: *0102 *0800 *efac *7ce4 *0003 *5b2c *1f61 *0000" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0030: *0000 *500b *0200 *0000 *0000 *1011 *1213 *1415" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0040: *1617 *1819 *1a1b *1c1d *1e1f *2021 *2223 *2425" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0050: *2627 *2829 *2a2b *2c2d *2e2f *3031 *3233 *3435" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0060: *3637" 2>&1 1>/dev/null])
> > +
> > +
> > +OVS_TRAFFIC_VSWITCHD_STOP
> > +AT_CLEANUP
> > +
> > +AT_SETUP([mpls - decap header slow-path])
> > +OVS_TRAFFIC_VSWITCHD_START()
> > +
> > +AT_CHECK(ovs-appctl dpif/set-dp-features br0 add_mpls false)
> > +ADD_NAMESPACES(at_ns0, at_ns1)
> > +
> > +ADD_VETH(p0, at_ns0, br0, "10.1.1.1/24", 36:b1:ee:7c:01:03)
> > +ADD_VETH(p1, at_ns1, br0, "10.1.1.2/24", 36:b1:ee:7c:01:02)
> > +
> > +dnl The flow will decap a mpls header which in turn carries a icmp packet
> > +dnl eth/mpls/eth/ip/icmp --> OVS --> eth/ip/icmp
> > +
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flow br0 "table=0,priority=100,dl_type=0x8847,mpls_label=2 actions=decap(),decap(packet_type(ns=0,type=0)),ovs-p1"])
> > +
> > +rm -rf p1.pcap
> > +NS_CHECK_EXEC([at_ns1], [tcpdump -l -n -xx -U -i p1 > p1.pcap &])
> > +sleep 1
> > +
> > +dnl The hex dump is an mpls packet encapsulating ethernet packet. pkt=eth/mpls/eth/ip/icmp
> > +dnl The packet is sent from p0(at_ns0) interface directed to
> > +dnl p1(at_ns1) interface
> > +NS_CHECK_EXEC([at_ns0], [$PYTHON3 $srcdir/sendpkt.py p0 00 00 00 00 00 02 00 00 00 00 00 01 88 47 00 00 21 40 36 b1 ee 7c 01 02 36 b1 ee 7c 01 03 08 00 45 00 00 54 03 44 40 00 40 01 21 61 0a 01 01 01 0a 01 01 02 08 00 ef ac 7c e4 00 03 5b 2c 1f 61 00 00 00 00 50 0b 02 00 00 00 00 00 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 > /dev/null])
> > +
> > +dnl Check the expected decapsulated on the egress interface
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0000: *36b1 *ee7c *0102 *36b1 *ee7c *0103 *0800 *4500" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0010: *0054 *0344 *4000 *4001 *2161 *0a01 *0101 *0a01" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0020: *0102 *0800 *efac *7ce4 *0003 *5b2c *1f61 *0000" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0030: *0000 *500b *0200 *0000 *0000 *1011 *1213 *1415" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0040: *1617 *1819 *1a1b *1c1d *1e1f *2021 *2223 *2425" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0050: *2627 *2829 *2a2b *2c2d *2e2f *3031 *3233 *3435" 2>&1 1>/dev/null])
> > +OVS_WAIT_UNTIL([cat p1.pcap | egrep "0x0060: *3637" 2>&1 1>/dev/null])
> > +
> > +
> > +OVS_TRAFFIC_VSWITCHD_STOP
> > +AT_CLEANUP
> > +
> > +
> > +AT_SETUP([datapath - Encap Decap mpls actions])
> > +OVS_TRAFFIC_VSWITCHD_START([_ADD_BR([br1])])
> > +
> > +ADD_NAMESPACES(at_ns0, at_ns1)
> > +
> > +ADD_VETH(p0, at_ns0, br0, "10.1.1.1/24")
> > +ADD_VETH(p1, at_ns1, br1, "10.1.1.2/24")
> > +
> > +AT_CHECK([ip link add patch0 type veth peer name patch1])
> > +on_exit 'ip link del patch0'
> > +
> > +AT_CHECK([ip link set dev patch0 up])
> > +AT_CHECK([ip link set dev patch1 up])
> > +AT_CHECK([ovs-vsctl add-port br0 patch0 -- set interface patch0 ofport_request=100])
> > +AT_CHECK([ovs-vsctl add-port br1 patch1 -- set interface patch1 ofport_request=100])
> > +
> > +AT_DATA([flows.txt], [dnl
> > +table=0,priority=100,in_port=ovs-p0 actions=encap(mpls(ether_type=0x8847)),set_mpls_label:2,encap(ethernet),set_field:00:00:00:00:00:02->dl_dst,set_field:00:00:00:00:00:01->dl_src,output:100
> > +table=0,priority=100,in_port=100,dl_type=0x8847,mpls_label=2 actions=decap(),decap(packet_type(ns=0,type=0)),ovs-p0
> > +])
> > +
> > +AT_DATA([flows1.txt], [dnl
> > +table=0,priority=100,in_port=ovs-p1 actions=encap(mpls(ether_type=0x8847)),set_mpls_label:2,encap(ethernet),set_field:00:00:00:00:00:02->dl_dst,set_field:00:00:00:00:00:01->dl_src,output:100
> > +table=0,priority=100,in_port=100,dl_type=0x8847,mpls_label=2 actions=decap(),decap(packet_type(ns=0,type=0)),ovs-p1
> > +])
> > +
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flows br0 flows.txt])
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flows br1 flows1.txt])
> > +
> > +NS_CHECK_EXEC([at_ns0], [ping -q -c 3 -i 0.3 10.1.1.2 | FORMAT_PING], [0], [dnl
> > +3 packets transmitted, 3 received, 0% packet loss, time 0ms
> > +])
> > +
> > +
> > +NS_CHECK_EXEC([at_ns1], [ping -q -c 3 -i 0.3 10.1.1.1 | FORMAT_PING], [0], [dnl
> > +3 packets transmitted, 3 received, 0% packet loss, time 0ms
> > +])
> > +
> > +OVS_TRAFFIC_VSWITCHD_STOP
> > +AT_CLEANUP
> > +
> > +AT_SETUP([datapath - multiple encap decap mpls actions])
> > +OVS_TRAFFIC_VSWITCHD_START([_ADD_BR([br1])])
> > +
> > +ADD_NAMESPACES(at_ns0, at_ns1)
> > +
> > +ADD_VETH(p0, at_ns0, br0, "10.1.1.1/24")
> > +ADD_VETH(p1, at_ns1, br1, "10.1.1.2/24")
> > +
> > +AT_CHECK([ip link add patch0 type veth peer name patch1])
> > +on_exit 'ip link del patch0'
> > +
> > +AT_CHECK([ip link set dev patch0 up])
> > +AT_CHECK([ip link set dev patch1 up])
> > +AT_CHECK([ovs-vsctl add-port br0 patch0 -- set interface patch0 ofport_request=100])
> > +AT_CHECK([ovs-vsctl add-port br1 patch1 -- set interface patch1 ofport_request=100])
> > +
> > +AT_DATA([flows.txt], [dnl
> > +table=0,priority=100,in_port=ovs-p0 actions=encap(mpls(ether_type=0x8847)),set_mpls_label:3, encap(mpls(ether_type=0x8847)),set_mpls_label:2,encap(ethernet),set_field:00:00:00:00:00:02->dl_dst,set_field:00:00:00:00:00:01->dl_src,output:100
> > +table=0,priority=100,in_port=100,dl_type=0x8847,mpls_label=2 actions=decap(),decap(packet_type(ns=1,type=0x8847)),decap(packet_type(ns=0,type=0)),ovs-p0
> > +])
> > +
> > +AT_DATA([flows1.txt], [dnl
> > +table=0,priority=100,in_port=ovs-p1 actions=encap(mpls(ether_type=0x8847)),set_mpls_label:3, encap(mpls(ether_type=0x8847)),set_mpls_label:2,encap(ethernet),set_field:00:00:00:00:00:02->dl_dst,set_field:00:00:00:00:00:01->dl_src,output:100
> > +table=0,priority=100,in_port=100,dl_type=0x8847,mpls_label=2 actions=decap(),decap(packet_type(ns=1,type=0x8847)),decap(packet_type(ns=0,type=0)),ovs-p1
> > +])
> > +
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flows br0 flows.txt])
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flows br1 flows1.txt])
> > +
> > +NS_CHECK_EXEC([at_ns0], [ping -q -c 3 -i 0.3 10.1.1.2 | FORMAT_PING], [0], [dnl
> > +3 packets transmitted, 3 received, 0% packet loss, time 0ms
> > +])
> > +
> > +
> > +NS_CHECK_EXEC([at_ns1], [ping -q -c 3 -i 0.3 10.1.1.1 | FORMAT_PING], [0], [dnl
> > +3 packets transmitted, 3 received, 0% packet loss, time 0ms
> > +])
> > +
> > +OVS_TRAFFIC_VSWITCHD_STOP
> > +AT_CLEANUP
> > +
> > +AT_SETUP([datapath - encap mpls pop mpls actions])
> > +OVS_TRAFFIC_VSWITCHD_START([_ADD_BR([br1])])
> > +
> > +ADD_NAMESPACES(at_ns0, at_ns1)
> > +
> > +ADD_VETH(p0, at_ns0, br0, "10.1.1.1/24", 36:b1:ee:7c:01:03)
> > +ADD_VETH(p1, at_ns1, br1, "10.1.1.2/24", 36:b1:ee:7c:01:02)
> > +
> > +AT_CHECK([ip link add patch0 type veth peer name patch1])
> > +on_exit 'ip link del patch0'
> > +
> > +AT_CHECK([ip link set dev patch0 up])
> > +AT_CHECK([ip link set dev patch1 up])
> > +AT_CHECK([ovs-vsctl add-port br0 patch0 -- set interface patch0 ofport_request=100])
> > +AT_CHECK([ovs-vsctl add-port br1 patch1 -- set interface patch1 ofport_request=100])
> > +
> > +AT_DATA([flows.txt], [dnl
> > +table=0,priority=100,dl_type=0x0800 actions=decap,encap(mpls(ether_type=0x8847)),set_mpls_label:2,encap(ethernet),mod_dl_dst:36:b1:ee:7c:01:02,mod_dl_src:36:b1:ee:7c:01:03,output:100
> > +table=0,priority=100,dl_type=0x8847,mpls_label=2 actions=pop_mpls:0x0800,resubmit(,3)
> > +table=0,priority=10 actions=resubmit(,3)
> > +table=3,priority=10 actions=normal
> > +])
> > +
> > +AT_DATA([flows1.txt], [dnl
> > +table=0,priority=100,dl_type=0x0800 actions=decap,encap(mpls(ether_type=0x8847)),set_mpls_label:2,encap(ethernet),mod_dl_dst:36:b1:ee:7c:01:03,mod_dl_src:36:b1:ee:7c:01:02,output:100
> > +table=0,priority=100,dl_type=0x8847,mpls_label=2 actions=pop_mpls:0x0800,resubmit(,3)
> > +table=0,priority=10 actions=resubmit(,3)
> > +table=3,priority=10 actions=normal
> > +])
> > +
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flows br0 flows.txt])
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flows br1 flows1.txt])
> > +
> > +NS_CHECK_EXEC([at_ns0], [ping -q -c 3 -i 0.3 10.1.1.2 | FORMAT_PING], [0], [dnl
> > +3 packets transmitted, 3 received, 0% packet loss, time 0ms
> > +])
> > +
> > +NS_CHECK_EXEC([at_ns1], [ping -q -c 3 -i 0.3 10.1.1.1 | FORMAT_PING], [0], [dnl
> > +3 packets transmitted, 3 received, 0% packet loss, time 0ms
> > +])
> > +
> > +OVS_TRAFFIC_VSWITCHD_STOP
> > +AT_CLEANUP
> > +
> > +AT_SETUP([datapath - push mpls decap mpls actions])
> > +OVS_TRAFFIC_VSWITCHD_START([_ADD_BR([br1])])
> > +
> > +ADD_NAMESPACES(at_ns0, at_ns1)
> > +
> > +ADD_VETH(p0, at_ns0, br0, "10.1.1.1/24", 36:b1:ee:7c:01:03)
> > +ADD_VETH(p1, at_ns1, br1, "10.1.1.2/24", 36:b1:ee:7c:01:02)
> > +
> > +AT_CHECK([ip link add patch0 type veth peer name patch1])
> > +on_exit 'ip link del patch0'
> > +
> > +AT_CHECK([ip link set dev patch0 up])
> > +AT_CHECK([ip link set dev patch1 up])
> > +AT_CHECK([ovs-vsctl add-port br0 patch0 -- set interface patch0 ofport_request=100])
> > +AT_CHECK([ovs-vsctl add-port br1 patch1 -- set interface patch1 ofport_request=100])
> > +
> > +AT_DATA([flows.txt], [dnl
> > +table=0,priority=100,dl_type=0x0800 actions=push_mpls:0x8847,set_field:2->mpls_label,output:100
> > +table=0,priority=100,dl_type=0x8847,mpls_label=2 actions=decap,decap(packet_type(ns=1,type=0x0800)),encap(ethernet),mod_dl_dst:36:b1:ee:7c:01:03,mod_dl_src:36:b1:ee:7c:01:02,resubmit(,3)
> > +table=0,priority=10 actions=resubmit(,3)
> > +table=3,priority=10 actions=normal
> > +])
> > +
> > +AT_DATA([flows1.txt], [dnl
> > +table=0,priority=100,dl_type=0x0800 actions=push_mpls:0x8847,set_field:2->mpls_label,output:100
> > +table=0,priority=100,dl_type=0x8847,mpls_label=2 actions=decap,decap(packet_type(ns=1,type=0x0800)),encap(ethernet),mod_dl_dst:36:b1:ee:7c:01:02,mod_dl_src:36:b1:ee:7c:01:03,resubmit(,3)
> > +table=0,priority=10 actions=resubmit(,3)
> > +table=3,priority=10 actions=normal
> > +])
> > +
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flows br0 flows.txt])
> > +AT_CHECK([ovs-ofctl -Oopenflow13 add-flows br1 flows1.txt])
> > +
> > +NS_CHECK_EXEC([at_ns0], [ping -q -c 3 -i 0.3 10.1.1.2 | FORMAT_PING], [0], [dnl
> > +3 packets transmitted, 3 received, 0% packet loss, time 0ms
> > +])
> > +
> > +NS_CHECK_EXEC([at_ns1], [ping -q -c 3 -i 0.3 10.1.1.1 | FORMAT_PING], [0], [dnl
> > +3 packets transmitted, 3 received, 0% packet loss, time 0ms
> > +])
> > +
> > +OVS_TRAFFIC_VSWITCHD_STOP
> > +AT_CLEANUP
> > +
> > AT_SETUP([datapath - basic truncate action])
> > AT_SKIP_IF([test $HAVE_NC = no])
> > OVS_TRAFFIC_VSWITCHD_START()
> >
>
More information about the dev
mailing list