[ovs-discuss] 回复: 回复: How to configure in-band control in OpenvSwitch?

Justin Pettit jpettit at nicira.com
Thu May 3 07:26:00 UTC 2012


You don't need to do it with OVS commands.  You can just use ifconfig, ip, dhclient...

--Justin


On May 3, 2012, at 12:21 AM, 星言 墨虚 wrote:

> But I cannot find a command of ovs-vsctl could assign the IP address to bridge just like br0.
> So how to add an IP address to br0?
> 
> Thanks.
> 
> -- Tony
> 
> 发件人: Justin Pettit <jpettit at nicira.com>
> 收件人: 星言 墨虚 <beyond1680 at yahoo.cn> 
> 抄送: Ben Pfaff <blp at nicira.com>; ovs-discuss <discuss at openvswitch.org> 
> 发送日期: 2012年5月3日, 星期四, 下午 2:23
> 主题: Re: [ovs-discuss] 回复: How to configure in-band control in OpenvSwitch?
> 
> Even B can't connect to the controller?  That should be pretty basic connectivity. Are the IP addresses on the devices attached to the bridge or the bridge itself? Based on your drawing it looks like they're on the devices, which won't work. What happens if you assign the IP addresses to the bridge?
> 
> --Justin
> 
> 
> On May 2, 2012, at 11:13 PM, 星言 墨虚 <beyond1680 at yahoo.cn> wrote:
> 
>> Thanks, but I want to know how to add "hidden" rules to OpenvSwitch?
>> For example,
>> 
>> A(eth0) -------- (eth0)B(eth1) ------ (eth0)controller
>>  10.0.0.1       10.0.0.2   11.0.0.1    11.0.0.2
>> 
>> I create a network like this. A and B is openvswitch. I configure openvswitch using this command
>> ovs-vsctl add-br br0
>> ovs-vsctl add-port br0 eth0
>> ovs-vsctl add-port br0 eth1
>> ovs-vsctl set-controller br0 tcp:11.0.0.2:6633
>> 
>> But, the openvswitches cannot connect to controller, what else should I do?
>> 
>> -- Tony 
>> 发件人: Ben Pfaff <blp at nicira.com>
>> 收件人: 星言 墨虚 <beyond1680 at yahoo.cn> 
>> 抄送: "discuss at openvswitch.org" <discuss at openvswitch.org> 
>> 发送日期: 2012年5月3日, 星期四, 上午 11:30
>> 主题: Re: [ovs-discuss] How to configure in-band control in OpenvSwitch?
>> 
>> On Thu, May 03, 2012 at 11:12:50AM +0800, 星言 墨虚 wrote:
>> > I want to configure OpenvSwitch in-band control and I read
>> > the Design Decisions In Open vSwitch which websit is
>> > http://openvswitch.org/cgi-bin/gitweb.cgi?p=openvswitch;a=blob;f=DESIGNBut
>> > there are not details about how to enable in-band control in
>> > OpenvSwitch.So, I want to know the steps to configure it.Thanks very
>> > much.-- Tony
>> 
>> You don't have to do anything to enable in-band control, because it is
>> enabled by default.
>> 
>> 
>> _______________________________________________
>> discuss mailing list
>> discuss at openvswitch.org
>> http://openvswitch.org/mailman/listinfo/discuss
> 
> 




More information about the discuss mailing list